The pattern notebook · dry
Mr. Wiggly Variant
How do you tie a Mr. Wiggly Variant?
Mr. Wiggly Variant is a dry fly pattern for trout, bass, panfish. Find its 9 materials and 10 tying steps below.
- Difficulty
- 3 of 5
- Target species
- trout, bass, panfish
- Pattern designer
- Charlie Piette (Greg Patterson variation)
Added to catalog · Updated
At the vise
Materials
- Hook: Gamakatsu B10S, size 6
- Foam Body: Blane Chocklett's Loco Foam, cut into strips approximately 2.5" long × 0.25" wide
- Middle Foam Layer: 2mm craft foam, cut into 2" × 0.25" strips
- Thread: 12/0 Semperfli Nano Silk
- Legs: Round rubber legs
- Wings: Round rubber legs
- Sighter: Small rectangle of foam (cut from excess body foam)
- Eyes (Optional): Red push pins
- Adhesives: Super glue (e.g., Loctite gel superglue)
Have some of these already? The app matches recipes against your inventory and helps you build a shopping list for the gaps.
Tying instructions
1. Prepare the Hook and Foam Body: Place the Gamakatsu B10S size 6 hook in your vise. Take a piece of Blane Chocklett's Loco Foam (approximately 2.5" long × 0.25" wide) and fold it in half to gauge the bug's size.
Pro Tip: When piercing the foam, start by piercing the shiny side first at the point where the head of the fly will start. Then pierce the matte side about a shank's length back toward the tail. This orientation ensures the shiny Loco Foam is visible from both the top and bottom of the finished fly, enhancing its light-refracting flash. It also eliminates the need to dub the hook shank.
2. Pierce the foam with the hook point so the body can wrap around the shank. Fold again and pierce a second time, ensuring the holes are about a shank's length apart.
Secure the Foam to the Hook: Slide the foam onto the hook shank. Apply a bead of super glue on top of the foam and insert a strip of 2mm craft foam (2" × 0.25") to create a sandwich for added buoyancy. Glue and fold the outer foam around the shank, securing it fully.
3. Create Body Segments: Start at the point where the hook exits the bottom of the foam. Lay the 12 Semperfli Nano Silk thread on top and make one wrap, pulling tension away from you to cinch the foam down. Add 2-3 more wraps and tighten. Apply a dab of Loctite gel superglue to the thread wraps for security. Repeat this process to create 5 segments: one tail, three body, and one head. Each segment is formed by wrapping thread slightly up the shank and pulling down to bulb out the foam.
4. Add Rubber Legs: On the third segment, cut rubber legs to half length then fold in half a second time and cut again for shorter legs. Position two sets around the body, lifting the thread to place them. Pull tight to flare the legs slightly. Secure with additional wraps and tension.
5. Install Wings: For the head segment, use 3 half strands of rubber legs. Tie them in like the smaller legs on the 3rd segment, positioning them slightly higher on the body. Secure with wraps.
6. Add the Sighter: Cut a small rectangle from the excess foam at the tail. Apply super glue to the head thread wraps and position the sighter on top. Secure with 1-2 thread wraps.
7. Finish the Head and Trim: Move the thread to the hook eye, peel back the head slightly, and add tight wraps. Hand whip finish (4-6 loops) to secure, avoiding the legs and foam. Trim excess thread. Shape the tail into a point, leaving it long. Trim legs to body length.
8. Optional Embellishments: Add eyes by dabbing super glue on trimmed red push pins and inserting them into the head.